netsh ipsec dynamic show qmfilter - Windows Vista - command


 
NETSH - Windows Vista / 2008

netsh » ipsec » dynamic » show » qmfilter

Microsoft Windows [Version 6.0.6001]
(C) Copyright 2006 Microsoft Corp.
c:\windows>netsh ipsec dynamic show qmfilter ? Usage: qmfilter [ name = ] | [ all ] [ [ type = ] (generic | specific) ] [ [ srcaddr = ] (ipv4 | ipv6 | ipv4-ipv4 | ipv6-ipv6 | dns | server) ] [ [ dstaddr = ] (ipv4 | ipv6 | ipv4-ipv4 | ipv6-ipv6 | dns | server) ] [ [ srcmask = ] (mask | prefix) ] [ [ dstmask = ] (mask | prefix) ] [ [ protocol = ] (ANY | ICMP | TCP | UDP | RAW | ) ] [ [ srcport = ] ] [ [ dstport = ] ] [ [ actioninbound = ] (permit | block | negotiate) ] [ [ actionoutbound = ] (permit | block | negotiate) ] [ [ resolvedns = ] (yes | no) ] Displays quick mode filter details from SPD. Parameters: Tag Value name -Name of the quick mode filter. type -Type of filter to display, either specific or generic. srcaddr - Source ip address (ipv4 or ipv6), address range, dns name, or server type. dstaddr -Destination ip address (ipv4 or ipv6), address range, dns name, or server type. srcmask -Source address mask or a prefix of 1 through 32. dstmask -Destination address mask or a prefix of 1 through 32. protocol -Can be ANY, ICMP, TCP, UDP, RAW, or an integer. srcport -Source port. A value of 0 means any port. dstport -Destination port. A value of 0 means any port. actioninbound -Action for inbound packets. actionoutbound -Action for outbound packets. resolvedns -Value of 'yes' displays the resolved dns name. Remarks: 1. If the type is not specified then both 'generic' and 'specific' filters are displayed. 2. Server type can be WINS, DNS, DHCP or GATEWAY. 3. If an address range is specified, the endpoints need to be specific addresses (not lists, or subnets) and of the same type (both should be v4 or both should be v6). Examples: 1. show qmfilter name=qmf 2. show qmfilter all srcaddr=192.134.135.133 proto=TCP 3. If 'all' is specified, all quick mode filters are displayed. 4. If source or destination address name is specified, only filters associated with that address are displayed.

NETSH / IPSEC / DYNAMIC / SHOW / QMFILTER

netsh ipsec dynamic show qmfilter - Windows Vista - command Displays quick mode filter details from SPD. / Windows Vista
netsh, ipsec, dynamic, show, qmfilter, cmd, command, Windows, Vista
Quick - Link:
netsh dhcpclient help
Displays help.
netsh p2p collab help
Displays a list of commands.
netsh interface ipv4 show compartments
Shows compartment parameters.
netsh ras diagnostics show all
Shows Remote Access Diag Report.
netsh interface portproxy add v6tov6
Adds an entry to listen on for IPv6 and proxy connect to via IPv6.
netsh wlan delete filter
Remove a wireless network from the wireless allowed or







Windows-10





Windows-10

... facebook.de
... Windows-10 FAQ
... Windows-10 Info


Become a Sponsor
... Your button here?





Displays quick mode filter details from SPD. / Windows Vista

HTTP: ... cmd/en/Windows_Vista/netsh/ipsec/dynamic/show/qmfilter.htm
0.156
17547

Disable auto start of the speech recognition in Windows 8.1 (turn off)?

 /

Change Mouse Pointer and Cursor size on Windows-10, (smaller, larger)?

 /

Executing commands from the explorer address bars in Q-Dir!

 /

Keep the Microsoft Windows PC on or put to sleep!

 /

RGB Pixel to Negativ!

 /

Die versteckten Dateien und Ordner werden nicht angezeigen, warum?

 /

What is disk management?

 /

Can my MS-Surface with Windows 10 be damaged by the tiny insects?

 /

Stars as traces On the desktop for Astronauts and Cosmonauts!

 /

How big is Windows 10, size on disk after install on an partition?

 /

Being able to turn off auto-arrange within directorys?

 /

Print Images in Windows 8.1 or Windows 10, how to!?

 /