NETSH - Windows 7 & Vista + Server 2008

netsh » ipsec » dynamic » show » rule

Microsoft Windows [Version 6.1.7000]
(C) Copyright 2009 Microsoft Corp.
C:\Windows>netsh ipsec dynamic show rule ? Usage: rule [ [ type = ] (transport | tunnel) ] [ [ srcaddr = ] (ipv4 | ipv6 | ipv4-ipv4 | ipv6-ipv6 | dns | server) ] [ [ dstaddr = ] (ipv4 | ipv6 | ipv4-ipv4 | ipv6-ipv6 | dns | server) ] [ [ srcmask = ] (mask | prefix) ] [ [ dstmask = ] (mask | prefix) ] [ [ protocol = ] (ANY | ICMP | TCP | UDP | RAW | ) ] [ [ srcport = ] ] [ [ dstport = ] ] [ [ actioninbound = ] (permit | block | negotiate) ] [ [ actionoutbound = ] (permit | block | negotiate) ] [ [ resolvedns = ] (yes | no) ] Displays rule details from SPD. Parameters: Tag Value type -Type of rule to display, either transport or tunnel. srcaddr -Source ip address (ipv4 or ipv6), address range, dns name, or server type. dstaddr -Destination ip address (ipv4 or ipv6), address range, dns name, or server type. srcmask -Source address mask or a prefix of 1 through 32. dstmask -Destination address mask or a prefix of 1 through 32. protocol -Can be ANY, ICMP, TCP, UDP, RAW, or an integer. srcport -Source port. A value of 0 means any port. dstport -Destination port. A value of 0 means any port. actioninbound -Action for inbound packets. actionoutbound -Action for outbound packets. resolvedns -Value of 'yes' displays the resolved dns name. Remarks: 1. Default for the type parameter is 'transport'. 2. Server type can be WINS, DNS, DHCP or GATEWAY. 3. If source or destination address name is specified, only rules associated with that address are displayed. 4. If an address range is specified, the endpoints need to be specific addresses (not lists, or subnets) and of the same type (both should be v4 or both should be v6). Examples: 1. show rule - shows both transport and tunnel rules 2. show rule type=transport srcaddr=192.134.135.133 proto=TCP

NETSH / IPSEC / DYNAMIC / SHOW / RULE

netsh ipsec dynamic show rule - Windows Seven - command Displays rule details from SPD. / Windows Seven
netsh, ipsec, dynamic, show, rule, cmd, command, Windows, Seven
Quick - Link:
netsh netio add
Adds a configuration entry to a table.
netsh branchcache smb dump
Displays a configuration script.
netsh nap client rename trustedservergroup
Renames trusted server group configuration.
netsh advfirewall set domainprofile
Sets properties in the domain profile.
netsh mbn show interfaces
Shows a list of Mobile Broadband interfaces on the system.
netsh advfirewall firewall set
Sets new values for properties of a existing rule.





Windows-10


Windows-10





Windows-10


Become a Sponsor
... Your button here?





HTTP: ... cmd/en/Windows_7/netsh/ipsec/dynamic/show/rule.htm
0.078

Was bitteschön ist das XPS von Windows-7/8.1/10?

 /

Recalculate the windows experience index at any time!

 /

How to format new hard drive, create new partition/volume in Windows 8.1/10?

 /

Quad-Explorer Q-Dir Defender Firewall Win-10, problem!

 /

Restore the location of the default profile folder on Windows 10!

 /

How to change the drive letter in Windows 10, DVD and USB drives?

 /

Klappt die PDF Vorschau in Windows 7?

 /

How to list (see) all users via command line?

 /