netsh routing ip ospf set virtif - Windows 2000/XP - command


 
NETSH - Windows XP/2000

netsh » routing » ip » ospf » set » virtif

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1986-2001 Microsoft Corp.
C:\WINDOWS>netsh routing ip ospf set virtif ? Usage: set virtif [transareaid=] [virtnbrid=] [transdelay=] [retrans=] [hello=] [dead=] [password=] Parameters: Tag Value transareaid - The IP address of the transit area virtnbrid - The router ID of the virtual neighbor. transdelay - The estimated number of seconds it takes to transmit a link state update packet over this interface. This value should take into account the transmission and propagation delays of the interface and network media. The default setting is 1 second. retrans - The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value should exceed the expected round-trip delay between any two routers on the attached network. However, if this value is not conservative, needless retransmissions result. The value needs to be larger on low-speed serial lines. A sample value for a local area network is 5 seconds. hello - The interval in seconds between transmissions of hello packets by the router on the interface. You can also click the arrows to select a new setting. This setting must be the same for all routers that are attached to a common network. The shorter the hello interval, the faster topological changes are detected. However, a shorter interval also results in more OSPF traffic. A sample value for an X.25 network is 30 seconds. A sample value for a local area network is 10 seconds. dead - The number of seconds before a neighboring router considers this router to be down. The router is determined to be down if a neighboring router does not receive a hello packet sent by this router within the specified interval. For example, if your hello interval setting is 15 seconds and your dead interval is 60 seconds, after sending four hello packets and receiving no acknowledgment or response, neighboring routers declare that this router is down. This setting should be an integral multiple of the hello interval (commonly 4). This value must be the same for all OSPF router interfaces attached to a common network segment. password - If passwords are enabled for the area (the default setting) the password used for this interface by using any combination of uppercase or lowercase letters or numbers. All interfaces in the same area that are on the same network must use identical passwords. Interfaces in the same area that are on different networks can have different passwords. By default, passwords are enabled and the password is 12345678. Passwords are transmitted in plaintext, so this option is for identification, not security. If this option is unavailable, you must enable passwords for the area. Remarks: Changes OSPF parameters for the specified virtual interface. Examples: set virtif 10.0.0.1 11.1.1.2 hello=15 dead=60

NETSH / ROUTING / IP / OSPF / SET / VIRTIF

netsh routing ip ospf set virtif - Windows 2000/XP - command Changes OSPF parameters for the specified virtual interface. / Windows 2000/XP
netsh, routing, ip, ospf, set, virtif, cmd, command, Windows, 2000/XP
Quick - Link:
netsh p2p idmgr delete
Deletes identities and groups.
netsh winsock show catalog
Displays contents of Winsock Catalog.
netsh routing ip delete preferenceforprotocol
Deletes preference for a specified protocol.
netsh interface ipv6 isatap set
Sets configuration information.
netsh routing ip set filter
Changes filter attributes on the specified interface.
netsh ras aaaa set
Sets configuration information.







Windows-10





Windows-10

... facebook.de
... Windows-10 FAQ
... Windows-10 Info


Become a Sponsor
... Your button here?





Changes OSPF parameters for the specified virtual interface. / Windows 2000/XP

HTTP: ... cmd/en/Windows_XP/netsh/routing/ip/ospf/set/virtif.htm
0.171
18397

Den App-Ordner bereinigen in Windows 8.1 und 8 (METRO)!

 /

Print or export search result data list from Explorer in Win 10, 8.1, 7 (xls, txt, html, csv)!

 /

Reboot Delete File Ex or Reboot Move File Ex!

 /

USA football mouse tracks!

 /

Taskmanager starten unter Windows!

 /

Unlock and delete Files and Folder via MS File-Explorer Context Menu?

 /

Kann ich StressMyPC einsetzen, um mein Dual-CPU-System zu stressen und testen?

 /

Can I customize the windows 8.1 and 10 local date and time?

 /

Can I uninstall The auto hide cursor?

 /

What does the number of pings per host in TraceRouteOK ?

 /

Rain drops on the Windows 10 PCs and Laptops!

 /

Microsoft Office 365 Desktop shortcuts on Windows 10?

 /